Hephaestos

I don't update the website enought. But a lot of new born in the light toolbox.

Every module have a debug Led who blink in a good reception make a morse SOS in case of problems.

The code was fully rebuild to allow commercial application
Full DMX
12 bits Curve on every chanel
No vidéo Flicker.
Better interference immunity, and good bandwidth neighborhood
RF69HW natif but fully RF12B compatible
Other RF module in 2.4Ghz or very long distance LoraWan

DMX XLR Neutrik in 5 or 3 points version
optional HF Module
Vin from 3.7 to 35V, protected against wrong polarity
One constant Current dimmer (max 6A) for high power led or DC Mottor
A debug Led
Quick and secure connector for led and VIN
i2c Bus for module communication.
With HF module 4 input/output pwm 12 bits, 6 analog Input/output , 1 digital Input/output.
Without HF module 6 input/output pwm 12 bits, 6 analog Input/output , 4 digital Input/output.
Fully programmable by Arduino

Little Swiss Knife, already programed, this the main système board to receive or send DMX and drive some wireless Leds or stuff. One Constant Currant 16 bits with little flicker output dimmer.

size	N/A
weight	N/A

DMX XLR Neutrik in 5 or 3 points version
optional HF Module
Vin from 3.7 to 35V, protected against wrong polarity
One constant Current dimmer (max 6A) for high power led or DC Mottor
A debug Led i2c Bus for module communication.
With HF module 4 input/output pwm 12 bits, 6 analog Input/output , 1 digital Input/output.
Without HF module 6 input/output pwm 12 bits, 6 analog Input/output , 4 digital Input/output.
Fully programmable by Arduino

Little, only one DMX connector

size	N/A
weight	N/A

16 chanels stackable with the swissBoard.
8 power chanels pwm 12 bits dimmed , 8 more chanels are on a HE10 port to connect an Arp-power or a clone.
64 boards can be chained for a total of 1024 chanels. It is a lot of Leds.
No Swissboard included

16 chanels pwm 12 bits low flicker, inspire by module PCA9685 from Adafruit

size	N/A
weight	N/A

4 pwm Channels constant current limited (max 6A) for power Leds or DC motor
Limit the constant current by solder a 2W resitor in each chanel. R = 0.7/Constant Amp
Stackable with the swissBoard mini.

For RGBW.

size	N/A
weight	N/A

8 Channels
Can be pulged on the I2C Board 16 circuits LED Dimmer to get the 16 channels or to an arpschuino.

8 chanels pwm dimmer extension.

size	N/A
weight	N/A

Sender DMX/HF
512 DMX chanels
Low interference
Automatic sync on free frequency
Acte as an Enttec Open DMX on every lighting software

Simple USB key as enttec Open DMX

size	N/A
weight	N/A

Upgrade version from the one build by arpschuino association from a common work
DMX start adress
Mode HF sender or HF to DMX receiver
512 chanels
automatic sync on free frequency
Don't saturate frequency band

DMX HF tranceiver

size	N/A
weight	N/A

DMX XLR Neutrik in 5 or 3 points version
One constant Current dimmer (max 6A) for high power led or DC Mottor
Vin from 3.7 to 35V, protected against wrong polarity
A debug Led
Quick and secure connector for led and VIN
Control with DMX + HF + potentiometer
One switch to select the mode (reception DMX+HF or reception DMX/HF sender)
one Dip switch for adress.

One chanel 12 bits version, constant current limited.

size	N/A
weight	N/A

17 pwm 12 bits chanels with curve and no flicker
8 chanels up to 19A max par circuit, 9 chanels up to 6A max.
VIN = 32 Amperes max.
DMX/HF receiver or sender
DMX Bridge
A LCD screen for DMX adress, mode selection (receiver HF+DMX, receiverHF/emetteur DMX, receiver DMX/ HF high power sender), and curve selection for each chanels.

Over-designed, in a metal or in a plastic case.

size	N/A
weight	N/A

6Amp max for each chanels
Adressable with a dipswitch.

Simple gradateur DMX 4 ou 6 circuits dans un boitier plastique ou basé sur un gradalabs.

size	N/A
weight	N/A

On a little Lipo 4S 5200MHA, autonomy ± 1h30 at full.
Very convenient, little and powerfull
Mini Led profile don't heat to much. You can print your gobo directly on translucent papper.
Dimmable by HF, DMX and potentiometer
Battery non supply

Powered by a12V ou li-po 4S battery.

size	N/A
weight	N/A

HF
Change the lens, you can directly screw it.
On a simple 18650 battery used in éléctronic cigarette you get a ± 3h at full autonomy by spot.
You can plug several 18650 battery in parralele with a anti-back diode, to incrase autonomy

single or on a 2, 3, 4, 6 bar, white and cold warm.

size	N/A
weight	N/A

DMX 5 points
DMX adress
Sender mode. Juste plug it with a DMX cable and it can remplace a HF sender
512 chanels
automatic sync on free frequency
Don't saturate frequency band

In DMX or HF, no more huge cable to your video beamer. Juste place it and done.

size	N/A
weight	N/A

VIN 12V-14.5V
On a little Lipo 4S 5200MHA, autonomy ± 1h30 at full for a 50W led.
Very convenient, little and powerfull
Perforated to be fixed on a microphone step
Builded with a swissboard mini
Dimmable by HF, DMX and potentiometer
Battery non supply

Builded with 100W, 50W ou 50W RVB mount on a simple dissipator, very usefull when you need a lot of power..

size	N/A
weight	N/A

Gooseneck Stand lamp HF
Power supply or 18650 battery
Can be controled by HF
Adressable
Potentiometer let the musician get manualy the luminosity control
2 contrôl mode (priority to the potentiometer or priority to HF)

For musicien to let real black control by the lighting guy.

size	N/A
weight	N/A

Electronics Boards:

For all your DMX and HF need, board to compose your system and need.

DMX/HF Senders:

Many versions:
For a HF system only one is needed. The swissboard and mini, the channels Dimmers 17 and mono current constant channel and the shutter can acte as a DMX receiver/HF sender.

DC Dimmers:

Dimmers DC for power Leds or DC motors.
The HF versions can be used as DMX+HF reception or HF sender.

HF Modules:

HF Modules of light or accessory.
On battery, very convenient to hide in mobile element, on a spinner, or simply on outdoor use when it is to complex to get an electrical ligne.

Electronics Boards: For all your DMX and HF need, board to compose your system and need.

DMX/HF Senders: Many versions: For a HF system only one is needed. The swissboard and mini, the channels Dimmers 17 and mono current constant channel and the shutter can acte as a DMX receiver/HF sender.

DC Dimmers: Dimmers DC for power Leds or DC motors. The HF versions can be used as DMX+HF reception or HF sender.

HF Modules: HF Modules of light or accessory. On battery, very convenient to hide in mobile element, on a spinner, or simply on outdoor use when it is to complex to get an electrical ligne.

Electronics Boards:

For all your DMX and HF need, board to compose your system and need.

DMX/HF Senders:

Many versions:
For a HF system only one is needed. The swissboard and mini, the channels Dimmers 17 and mono current constant channel and the shutter can acte as a DMX receiver/HF sender.

DC Dimmers:

Dimmers DC for power Leds or DC motors.
The HF versions can be used as DMX+HF reception or HF sender.

HF Modules:

HF Modules of light or accessory.
On battery, very convenient to hide in mobile element, on a spinner, or simply on outdoor use when it is to complex to get an electrical ligne.